Make a pool with their hands in the country – interesting, but also time-consuming task. Identify a place not only for the pool, but also a space for dredged material for building materials and technology approach.
When choosing a place to consider the proximity of the aqueduct, houses, baths (saunas). The pool should not be trees shed their leaves annually, as they contribute to water pollution. For sites under the pool is desirable small slope. This will decrease the amount of earthworks and significantly facilitate the work on the design of water drainage system of the basin. It is necessary to take into account the proximity of groundwater. If water has already appeared, it means that the zone at a depth of 0.5-1 m – problem.
Then we build a swimming pool in a small recess, the more that the proposed design allows it.
The project is designed on the flat area next to the sauna, without sanitation, water from wells, sandy soil. Technically, the sauna room is a pumping station for water saunas, houses, irrigation and basin management.
For swimming pools in the country use reinforced concrete ring DC-20-9 (5) with an outer diameter of 2,2 m to 0.9 m high base. Digging a trench for the pool. It should be larger (20-30 cm) intended basin and the pit walls is done with a certain slope (7,3 degrees) outwardly. The depth of the pit, too, should be more than 30-35 cm, in the center – 50 cm.
Then the ground at the bottom of the pit and align carefully rammed, it should be laid on a sandy base layer of 20-30 cm (6).
Much depends on the soil type. If clay soil, dig a trench to be deeper than projected in the 40-50 cm and fill the extra space with gravel and sand. Sandy soil to prevent subsidence have to strengthen further the concrete screed.
On top of the pillow put waterproofing, two layers of roofing material on the asphalt mastic. Install the ring (5). Wallpapers ring roofing material, fell asleep trench and compacted. You can simply fill up with clay and ram.
Ground strengthen reinforced screed (7). . The thickness of the tie 10 cm To improve the waterproofing properties of concrete ties in introducing additive – a mixture of penetrating waterproofing. Ties do with a slope of 3.5 degrees in the direction of the recess, the recess – 5 cm. It is necessary for the tube pump (10).
Next, make blind area (4) around the pool. The thickness for at least 10 cm from bricks (3) Put the curb – it protects the pool of meltwater. We are laying the pipe between the bricks (2, 8, 10). The tube pump (10) is assigned to the ladder, so as not to interfere with bathing. Tube filling connect to the water system through the valve. The pipe overflow derive into the pit, into a ditch, drain. pumping water pump is located in the sauna or in a small sealed dry well near a swimming pool. Tubes take better HDPE, they are not afraid razmerzaniya not electrically conductive. If you want to increase the depth of the pool, you can put a few rows of brick masonry. If you have children, the depth is sufficient.
We provide waterproofing the inside of the pool with a special mixture. Plasterer foundation, walls, border thickness of 3-4 mm.
After drying, the plaster sticking a special tile for pools. Since the pool round and has a curvature of the wall, it is better to glue the narrow tile – 5×10 cm, but you can try and 10×20 cm seams close up mastic.. Adhesive and sealant must be water-resistant and cold-resistant. After drying, the pool ladder set (9), is mounted on the anchors. Hole under the wall plugs and waterproof coat with mixture.
The use of reinforced concrete rings saves time and money and allows you to build a pool on any ground and at any location.
The water change every two or three weeks. You can add water bluestone, then the water is not long bloom and can be used for irrigation.
Good luck, my friends! Make the most inexpensive pool for children in the country – it is great, so it pays to work.
- Ground Level
- The pipe overflow
- Blind area
- Ring DK-20-9
- Drainage – CBC
- Gain screed floor
- Pipe for filling
- pumping pipe
- Self-priming pump